Este producto se vende actualmente.
NCR - Nicotine Reinforcer
Installation and preparations: Put the Wafer Heater into the deck slot and screw it with the Allen wrench. Check the resistance by connecting it with a MOD.(Wafer heater is usually pre-installed ex-work. Due to the different feature of various mods, resistance may range from 0.4-0.5ohm accordingly.)
How to fold the cottons: Pre-cut Organic cotton is strongly recommended. Cut each piece of cotton into a strip with the size of 8mm(width)* 40mm(length). Fold the cotton strips from middle and cover the wafer heater from the top and insert the cotton ends into the deck.
How to fix the cotton holder: Put on the aluminum cotton holder to fix the cotton strips. Make sure the cotton strips are fixed properly for E-juice soaking and vaporization. Moisten the new cotton with E-juice from all the openings on the top, bottom and all 4 sides of the cotton holder.
Output modes selection: The MOD with AOC Power modeï¼ˆAdjustable Output Curveï¼€°or Boosting mode is strongly recommended. To optimize the wafer heating function, please set up a considerably high wattageï¼ˆ70W-80Wï¼€°at the initial firing stage for around 0.5-1 second, then drop the wattage to a relatively low level(40W-50W) to last for another 2-3 seconds. Users may customize the Power mode settings to personal preference.
Clean the dirt and stains on the Wafer Heater: After being used for some time, you need to clean the Wafer Heater. Remove the cotton holder and give the Wafer Heater a dry burn at 30W-40W in 3 seconds. A fine grade sand paper can also be used to rubbed off the stubborn stains on the Wafer Heater. For regular maintenance you may use a toothbrush to clean the RDA deck and all connections with household detergents.
Features and Specs:
- Dimensions: 1-1/2" x 1" (Including Tip and Threads)
- WAFER Material: SST aluminum nitride
- WAFER Heater Resistance: 0.4-0.5ohm
- 510 thread
- Coil-free Design, No Wire Building
- 600,000 Times Cycle-use WAFER Heater(0.4-0.5ohm resistance)
- Visible Outer Cover with Venting Holes
- Strengthened Nicotine Effect
- Easy self-cleaning
Do not use Ni200 coils with non-temperature control devices/mods. This is a risk of battery explosion! Please make sure that the devices/mods that you are using is capable of controlling coil temperature.
This product is for advanced user only! Please have a great understanding and technical knowledge on how to use this product in order to properly use it
Warning: This tank is a Sub-Ohm resistance atomizer and only work on mechanical mod or devices that can handle Sub-Ohm resistance of 0.5ohm or lower. Please make sure you have a great understanding and technical knowledge on how to use mods and batteries that can handle Sub-Ohm coils. Do not use short or flat 510 connection on any hybrid or hybrid style device. If you are not familiar or unsure of particular products or set-ups, please do not use it. Always use proper precautions and handling.
Note: There is always an inherent risk when using any rechargeable batteries at anytime and under any circumstances. Vape Vandal and any of Vape Vandal's parent and subsidiary companies are not held responsible for any damage for any modification of the batteries, chargers, devices and other products that we carry in any form or shape, this is including pack making.
Vape Vandal and any or all of Vape Vandal's parent and subsidiary companies will not be held responsible or liable for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable battery/batteries as well as chargers. Please have a greater understanding of the batteries/chargers you are using and how to care for them properly.
This product is not covered by warranty and cannot be exchanged.